Energy savings

Wind solar turbine generator

vindkraftVelox Wind solar turbine generator
Art Nr: veloxvind

 Technical data JOC-500A-V JOC-1000A-V JOC-3000A-V JOC-5000A-V JOC-10KAV JOC-20KAV
Mill diameter (cm) 138 180 230 300 600 768
Startup wind speed (m/s) 2 2 2 2 2 3
Wind speed (m/s) 10 12 12 12 12 12
Rating power (W) 500 1000 3000 5 kW 10 kW 20 kW
Governed speed style AD* AD* AD* AD* AD* AD*
Pillar height (m) 5.5 5.5 5.5 11 11 11
Rated speed (RPM) 130 120 100 90 80 80
Blade length (cm) 220 200 470 600 620 960
Working wind speed (m/s) 40 45 50 55 55 55
Rated output DC 24V DC 36V DC 240~500V DC 240~600V DC 280-600V DC 400-600V
Brake style No need No need No need No need No need No need
Net weight (kg) 40 (no pillar) 46 (no pillar) 140 (no pillar) 180 (no pillar) 270 (no pillar) 290 (no pillar)

* Aerodynamic

Heat accumulator

CALO-BLOC HEAT ACCUMULATOR – ENVIRONMENT-FRIENDLY AND ECONOMCIAL HEATING

calob1Reloading point of warmth for heating and water heating

  • boiler for solid matters
  • tiled stove
  • fireplace
  • oil-fired boilers
  • gas-fired boilers
  • condensing boilers
  • solar collectors
  • heat pumps
  • electric energy

The presented interval technics are the consequent further development of the well-known low-temperature heating systems. The interval heating technics are the result of many years of experience and they are scientifically substantiated by extensive research of different institutes.

Burner cycles with and without CALO-Bloc

calob2

The interval heating technics bring lots of advantages:

  • solid plastics accumulator
  • rustproof
  • no reactive anodes
  • polyurethane compact insulation (CFC-free)
  • only 1,5°C reduction in 24h
  • insulation safety-tested by TÜV
  • easy to assemble
  • low transport weight
  • heat exchanger in assebly system
  • large storage capacity
  • constantly fresh warm industrial water
  • no health hazard by legionella
  • no smouldering fire
  • no soot problems
  • optimum utilization of power sources
  • long burner life
  • lowest stand-by losses
  • minimized turn-on and turn-off intervals
  • lowest burner wear and maintenance work
  • SOLAR for heating and hot water
  • intermediate storage of every energy as required
  • high yearly level of utilization
  • very environment-friendly
  • always expansible

Interval heating technics

As the CALO-Bloc Heat accumulator is included in the heating circuit the water volume of the heating system grows. So the burner starts much more rarely and enables an efficient and environment-friendly heating.

Operation with solid matters

The CALO-Bloc Heat accumulator makes it possible to store the really neeeded warmth temporarily. So a more economical use of fuel is possible.

Solar operation

The storage of warmth in the CALO-Bloc makes it possible to use solar energy even on days lacking in sunshine. The warmth cannot only be used to warm up service water, but it can also be used for heating.

Condensing technic

The rectangular parallel-piped-shaped structure  and the optimum arrangement of the heat exchangers guarantee a very good temperature-bedding in the accumulator. The low return temperature makes it possible to use the condensing warmth for heating as well as for warming up service water all year round.

Electric night storage

The CALO-Bloc Heat accumulator can be charged at very reasonable times and if necessary it can be discharged through the use of water or heating.

Operation with heat pumps

The temporary storage of warmth makes it possible to use the recovered warmth at a later time.

Hydraulics

  • You can l ink up to four heat accumulators without further circulating pumps with each other.
  • The pipe work should be done by “Tichelmann”, that is, the sum of the lengths of the flow and return pipes are the same at each connection.
  • If more than four heat accumulators are linked, an additional circulating pump is needed.

Regulation

  • The additional circulating pump should be operated with a separate difference-temperature-controller.
  • Possible regulations: DS100, DS100/D, DS200/D

Accessories

Part.no 7837 Heat exchanger (Copper pipes) CWT 10.2 Cu
22 m² with WT-range connections R 1 ” flange lid (stainless steel), brackets, installation screws and washers, working pressure up to 30 bar.
Weight: approx. 17kg
Reducement of power:
for hot water: -50 l/min (Tsp = 80°C)
-30 l/min (Tsp = 55°C)
WP-function up to 18 kW
Heat function up to 35 kW
for solar heating up to 10 m² collection range

Part.no 7838 Heat exchanger (Pipe in stainless steel) CWT 10.2 E
Performance and reducement of power the same as part.no 7837.

Part.no 7835 Heat exchanger (Copper pipes) CWT 10.3
11 m² WT-range. Performance as part.no 7837
Weight: approx. 9kg
Reducement of power:
WP-function up to 11 kW
Heat function up to 20 kW
for solar heating up to 10 m² collection range

Part.no 7809 Heat exchanger combination  CWT K-A
(Copper pipes) with WT-range totally 33m². Connection R 1 ” with flange lid (stainless steel), brackets, installation screws and washers, working pressure up to 30 bar, consisting of.
1 pc CWT 10.2 Cu Part.no 7837
1 pc CWT 10.3 Cu Part.no 7835
Weight: approx 26 kg
Reducement of power as part.no 7837 and 7835

Accessories

Screw-in heater AscoHeat
Part.no: 012-0200More info

ascoheat1Screw in heater AscoHeat

Part.no: 012-0200

A wide range of application

  • Drying up buildings when the heating system is not operating
  • As emergency heating in case of failure of the heating system.
  • Extra heat for air/water pumps
  • Extra heat for solar installations
  • 150mm non-heatead area for use in an energy-saving heat storage

Installation friendly

  • Integrated switch-off function -> no extra installation costs
  • Conical 1 ½” thread for ideal placement of cover
  • Quality spring clips (4mm²) for a safe and time saving electrical connection

Models

Right type for each installation:

  • Type A with temperature control and safety thermostat (basic design)
    Practical temperature setting by means of a rotating knob
  • Type A with temperature monitor and safety thermostat (basic design)
    Protected against accidental maladjustment (internal adjustement)
  • Type B with remote control (optional)
    Direct activation from an electrical heat control by means of an integrated switch-off function.
  • Type C with manual/remote control selector switch (optional)
    Selector switch for manual activation or direct activation from an electric heating regulator by means of an integrated switch-off function.

Right material for your installation

  • Industrial water:
    Heater manufactured of special alloy Cronifer 1.4529
  • Water heater
    Heater manufactured of high-class alloy CN 18/8 1.4541
  • Ambient temperature
    Polycarbonate cover for high temperatures

Protection against splashing water IP54

For harsch conditions the ASKOHEAT heater be adapted with a temperature monitor (internal adjustment) with IP54 class.

instick1
Flanged radiator heater AscoHeat-F
Part.no: 012-0300More info

ascoheatfFlanged radiator heater AscoHeat-F

Part.no: 012-0300

A wide range of application

  • Extra heat for solar system for treatment of industrial water
  • Extra heat for air/water pumps
  • As emergency heating in case of failure of the heating system.
  • For drying-up buildings when the heating system not is operating

Installation friendly

  • Integrated switch-off function -> no extra installation costs
  • Electrical insulated heaters
  • Quality spring clips (4mm²) for a safe and time-saving electrical connection

Models

Right type for each installation:

  • Type A with temperature control and safety thermostat (basic design)
    Practical temperature settings by means of a rotating knob
  • Type A with temperature monitor and safety thermostat (basic design)
    Protected against accidental maladjustment (internal adjustment)
  • Type B with remote control (optional)
    Direct activation from an electrical heating control by means of an integrated switch-off function.
  • Type C with manual/remote control operating switch (optional)
    Opeating switch for manual activation or direct activation from an electrical heating regulator by means of an integrated switch-off function.

Right material for your installation

  • Industrial water:
    Heater manufactured of special alloy Cronifer 1.4529
  • Water heater
    Heater manufactured of high-class alloy CN 18/8 1.4541
  • Ambient temperature
    Polycarbonate cover for high temperatures

Protected against limescale formation

  • Low surface power/Low radius for reduction of limescale formation
instick2